1.Tools Box&Pump Room

Structure	The main frame structure is welded with high-quality square pipes, and the outer decorative panel is welded with carbon steel plates. The roof is non-slip and walkable. There are flip pedals on both sides and non-slip design.
Tools Box	The equipment box is located on both sides of the rear of the passenger compartment, with aluminum alloy rolling shutter doors and lighting lights inside. There are storage boxes in the equipment compartment according to requirements. There is a flip pedal on the lower side.
Pump Room	The pump room is located at the rear of the vehicle, with aluminum alloy rolling shutters on both sides and back, with lighting lamps inside, and turning pedals at the lower sides of the pump room.
	Heat preservation position: install fuel heater (optional according to customer needs, suitable for use in areas with low winter temperature in the north)
Ladder and car handle	The rear ladder is made of aluminum alloy two-section flip ladder. When used, it should not exceed 350mm from the ground. The handle of the car adopts a grooved non-slip round steel pipe with a plastic spray treatment on the surface.
2、Water Tank
Capacity	3800kg（PM50）、4200kg（SG50）
Materils	High-quality carbon steel with a thickness of 4mm (can be made of stainless steel and PP according to user requirements)
Tank Fixed Position	Flexible connection with chassis frame
Configuration of Tank	Manhole: 1 manhole with a diameter of 460mm, with quick lock/open device
	Overflow port: 1 DN65 overflow port
	Remaining water outlet: set a DN40 water tank to discharge the remaining water outlet, equipped with a ball valve
	Water injection port: connect 2 DN65 ports on the left and right sides of the water tank
	Water inlet and outlet: set 1 water tank to the water pump inlet pipe, DN100 valve, which can be controlled pneumatically and manually, set 1 water pump to the water tank filling pipe, DN65 valve, can be controlled pneumatically or manually

3.Foam Tank

Capacity	1400kg（PM50）
Materils	4mm
Tank Fixed Position	Flexible connection with chassis frame
Configuration of Tank	Manhole: 1 DN460 manhole, with quick lock/open, automatic pressure relief device
	Overflow port: 1 DN40 overflow port
	Remaining liquid port: set up a DN40 foam tank to discharge residual liquid port
	Foam outlet: set a DN40 foam tank to the foam pipe of the water pump

4.Water System

(1)Water Pump

Model	CB10/30-RS type low pressure vehicle fire pump
Type	Low pressure centrifugal
Rated Flow	30L/s @1.0MPa
Rated outlet pressure	1.0MPa
Maximum water absorption depth	7m
Water diversion device	Self-contained sliding vane pump
Water diversion time	In max water diversion device≤50s

(2) Piping system

Materils of Pipe	High quality seamless steel pipe
Suction line	1 DN100 suction port on the left and right sides of the pump room
Water injection pipeline	There are 2 DN65 water injection ports on the left and right sides of the water tank, and a DN65 water pump is installed in the pump room to inject water into the tank.
Outlet pipeline	There are 1 DN65 water outlets on the left and right sides of the pump room, with a scenter valve and a cover
Cooling water pipeline	Cooling water pipeline and control valve equipped with cooling power take-off

5.Fire Fighting Configuration
(1) Car water cannon

Model	PS30W
OEM	Chengdu West Fire Machinery Co., Ltd.
Rotation Angle	360°
Max Elevation Angle/Depression Angle	Depression Angle≤-15°，Elevation Angle≥+60°
Rated Flow	40L/S
Range	≥50m

(2) Car Foam Cannon

Model	PL24
OEM	Chengdu West Fire Machinery Co., Ltd.
Rotation Angle	360°
Max Elevation Angle/Depression Angle	Depression Angle≤-15°，Elevation Angle≥+60°
Rated Flow	32L/S
Range	Foam≥40m  Water≥50m

 6.Fire Fighting Control System

The control panel mainly includes two parts: cab control and pump room control

Control in Cab	Water pump off gear, warning light alarm, lighting and signal device control, etc.
Control in Pump Room	Main power switch, parameter display, status display

7.Electrical Equipment